Electrical Electronics Engineering Research Papers/Topics

CONSTRUCTION OF EQUIPMENT FOR DEODORIZING KEROSENE

ABSTRACT The motive of this project is to construct  equipment for deodorizing kerosene, hence the smell of kerosene is totally eradicated. The equipment was constructed with flat sheet plates of a desired standard, the dimension and the truncated parts were coupled and welded in order to fasten the parts together.  The material was selected to avoid the effect of rust due to the contact of the separating items or material with the walls of metal sheet. The effect of this equipment will be ...

CONSTRUCTION OF ORSAT GAS ANALYZER

ABSTRACT The Orsat Gas Analyzer was constructed at the project development institute (PRODA), Enugu.  The operation involved the laboratory glass blowing which entails the heating of a glass tube. The heating •continues until the glass tube reaches its plastic state. The shape of the tube is changed or the required shape blown by pulling, bending by hand, cutting with a knife and also blown with mouth or denting the shape by the application of a suitable tool.  The selection of the materi...

THE CURRENT STATUS AND FUTURE CHALLENGES OF ELECTRICITY MARKET IN NIGERIA IN THE FACE OF DEREGULATION

ABSTRACT Electricity is fundamental and inevitable to our daily living as it lighting our environment, powers our homes, schools, hospitals, offices, businesses, and aid industrialization, It is a known phenomena that the economic growth of a nation rides on the wheel of electricity. While the telecommunication market in Nigeria has recorded advancement and stability, electricity market in Nigeria is facing mix challenges ranging from slow growth in generation capacity (generation capacity pe...

USE OF SOLAR ENERGY RATHER THAN ELECTRIC ENERGY TO CHARGE CELL PHONE

INTRODUCTION In today’s quest for electrical energy and increasing hazards in our environment, alternatives to the use of non – renewable and polluting fossil fuels have to be investigated. One such alternative is SOLAR ENERGY.  Solar energy is quite simply, the energy produced directly from the sun and collected elsewhere, on earth. The sun creates its energy through a thermonuclear process that converts about 650,000,000 tons of hydrogen to helium every second. The process creates heat...

DESIGN AND IMPLEMENTATION OF BIOMETRIC FEATURES PRE-PROCESSING

The need for identification leads to the study of biometrics. Over the ages, human beings have been identified by various means, such as the Name, Complexion, Nationality, and even some uniquely assigned codes. Of all these methods, none can be used to uniquely identify an individual distinctly under all circumstances. However, research has shown that an individual‟s biometric feature can be used to uniquely identify them, under all circumstances. For these biometric features to be appropri...

DESIGN AND FABRICATION OF A 12M3 MOBILE DEEP FREEZER

ABSTRACT This write up is a detail of the process and information of plan for the physical realization of the construction of the 1M3 mobile deep freezer. It is divided into chapters, which discussed extensively the practical refrigeration cycle with full attention given to design factors working principle and choice of material. The method used in fabrication, assembly and driving the safety requirement was not left out.   TABLE OF CONTENT Title Page i Release Page ii Signature Pageiii  Ap...

DESIGN AND CONSTRUCT A MULTIREMOTE CONTROLLER USING INFRA-RED MODE OF TRANSMISSION

ABSTRACT Microcontroller based remote control system is a project design of a system that uses infra red transmission and reception principle to switch on or off other appliances. It is a wireless mode of switching appliances to a desired state. When a number is pressed in the transmitter section, the receiver section decodes the signal and utilizes it in controlling the desired appliances. Several functional blocks of circuit are put together to ensure that the design works as the designer ...

Design and Construction of an Automatic Power Changeover Switch

Abstract Power failure or outage in general does not promote development to public and private sector. The investors do not feel secure to come into a country with constant or frequent power failure. These limit the development of industries. In addition there are processes that cannot be interrupted because of their importance, for instance surgery operation in hospitals, transfer of money between banks and lots more. This paper presents the design and construction of an automatic power chan...

Design Of A Patient Heartbeat And Temperature Monitor Using RF

The major aim and objective of this design [of a patient heartbeat and temperature monitor using RF.] is to help the doctors and family members to keep track of the heartbeat condition of their loved ones [as well as their body temperature] in the case of an abnormality in the health condition (for those with heartbeat defects and those that run excessive high temperature beyond normal). If any varied change takes place, it is notified. This notification through RF. Channel would to take an a...

Home Control Switch Automation Using Gsm Communication

ABSTRACT The advantage of cellular communication like GSM technology is a potential solution for such remote controlling activities. GSM-SMS technology can be used to control household appliances from remote places. Remotely, the system allows the home owner to monitor and control his house appliances via his mobile phone set by sending commands in the form of SMS message and receiving the appliances status as well. This system provides ideal solution to the problems caused in situations when...

Design And Construction of Automatic Phase Selector

The scope of the project covers aspects like the features of automatic three phase selector, its applications, and its operations. Its advantages and its components. Finally, it covers the importance on the need of automatic three phase selector and contributions toward a greater sharing load balance and a better three phase power distribution and monitoring for domestics consumers. INTRODUCTION As the growing population of human race widens the gulf between energy supply and energy demand, ...

Design And Construction Of An Inverter Type Arc Welding Machine

The main aim and objective of this project is to design and build and arc welding machine that operates on 36vdc at variable frequency which of benefit to urban area. This reduces the weight and size of the transformer use for welding. To have an arc welding machine that is more efficient which produce neat welding. INTRODUCTION Welding is a way of heating pieces of metal using electricity or a flame so that they melt and stick together. It can simply be defined as the process of joining two...

Design And Construction Of 20 Watts Wireless Public Address System

ABSTRACT It has become inevitable that there would be communication and due to the inherent limitation of the human voice, the public address system came to being. A public address or “P.A SYSTEM” is an electronic amplification system with a mixer ,amplifier and loudspeakers, used to reinforce a given sound , e.g a person making a speech, pre-recorded music ,or message and distributing the sound throughout a venue . The voice signal is passed through a microphone , which converts the sou...

CONSTRUCTION OF RADIO FREQUENCY GSM SIGNAL JAMMER

This project is mainly intended to prevent the usage of mobile phones in places inside it coverage without interfering with communication channels outside it range, thus providing a cheap and reliable method for blocking mobile communication in the required restricted area only. Although we must be aware of the fact that nowadays lot of mobile phones can easily negotiate the jammer effect are available and therefore advance measures should be taken to jam such type of devices. The main disadv...

CONSTRUCTION OF AUTOMATIC WATER LEVEL CONTROLLER FOR BOTH OVERHEAD AND UNDERGROUND TANKS

ABSTRACT Automatic water level controller for both overhead and underground tank is designed to monitor the level of water in a tank. It displays the level of water and when it is at the lowest level; a pump is activated automatically to refill the tank. When the tank is filled to its maximum capacity, the pump is automatically de-energized. Several circuits are put together to ensure proper working of this design, and the block diagram includes the supply unit, the micro-processor unit, the ...


496 - 510 Of 512 Results