THE FABRICATION FOR A SET OF SIEVES AND SAKER

ABSRACT

The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component parts of the sets of sieve and their dimensions are as follows:
Height of sieve 5.5cm
Number of sieves 7
Diameter of sieve 13.5cm
Shape of sieve circular
Height of sieve set 44cm
In fabricating this set of sieves, some factors were taken into consideration and they are:
The capacity of the sieve.
The type of mixture that can be filtered in it.
The types of properties and composition of the mixture.
The type of material to be used for fabrication of the sieve and shaker.
The mechanism of the filtration process and also,
The cost, which is the determinant, factor in fabrication of any equipment.
These factors help greatly in the fulfillment of the objective of this project study. And after fabrication the projects were tested and seem to be working very efficiently with a reasonable separation of particle and cut diameter.
Using the above dimensions, the following fabrication procedures were undertaken, layout, cutting, drilling, welding, filling sand papering, washing and painting, drying assembling.
Finally,  the set of sieves and shaker were subjected to the process of washing, painting and drying.


TABLE OF CONTENT

Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of content

CHAPTER ONE
1.0INTRODUCTION

CHAPTER TWO
2.0LITRATURE REVIEW
2.1Model
2.2Screening
2.3Types of screens
2.4Screen surface
2.5Factors in selecting screen equipment
2.6Method of feed

CHAPTER THREE
3.0MATERIAL OF CONSTRUCTION
3.1Aluminum and aluminum alloy
3.2Carbon and low alloys steel
3.3Corrosion 
3.4Contact or galvanic corrosion

CHAPTER FOUR
4.0FABRICATIONAL PROCEDURE
4.1Layout
4.2Cutting
4.3Drilling
4.4Welding
4.5Filling
4.6Sand papering
4.7Washing and painting
4.8Drying
4.9Assembling

CHAPTER FIVE
5.0OPERATION AND MANTENANCE
5.1Function of some parts of the electrically vibrated screen.

CHAPTER SIX
6.0RECOMMENDATION AND CONCLUSION
6.1Costing 
REFERENCE.

Subscribe to access this work and thousands more
Overall Rating

0

5 Star
(0)
4 Star
(0)
3 Star
(0)
2 Star
(0)
1 Star
(0)
APA

Kings, S. (2018). THE FABRICATION FOR A SET OF SIEVES AND SAKER. Afribary. Retrieved from https://afribary.com/works/the-fabrication-for-a-set-of-sieves-and-saker-5967

MLA 8th

Kings, Solomon "THE FABRICATION FOR A SET OF SIEVES AND SAKER" Afribary. Afribary, 29 Jan. 2018, https://afribary.com/works/the-fabrication-for-a-set-of-sieves-and-saker-5967. Accessed 30 May. 2024.

MLA7

Kings, Solomon . "THE FABRICATION FOR A SET OF SIEVES AND SAKER". Afribary, Afribary, 29 Jan. 2018. Web. 30 May. 2024. < https://afribary.com/works/the-fabrication-for-a-set-of-sieves-and-saker-5967 >.

Chicago

Kings, Solomon . "THE FABRICATION FOR A SET OF SIEVES AND SAKER" Afribary (2018). Accessed May 30, 2024. https://afribary.com/works/the-fabrication-for-a-set-of-sieves-and-saker-5967

Document Details
Field: Chemical Engineering Type: Project 45 PAGES (6270 WORDS) (doc)