ABSTRACT -The paper presents a productivity model with an inflation component based on an 'established productivity measurement theory. The motivation for writing this paper is the need for conflict resolution at the implementation of productivity incentive programs. A common complaint from trade unions and organizations is that productivity is inaccurately assessed when the traditional inputoutput approach is utilized. The support for this argument is that a general rise in prices of materia...
Abstract Measurements have been made in a turbulent boundary layer which is subjected to a short roughness strip, with the view to examine the influence of short roughness strip on the large scale motion. This is quantified through the analysis of autocorrelation of the fluctuating velocities in the streamwise and wall-normal downstream of a roughness strip. Also, distributions of cross correlation functions are presented. The results indicate that, reference to the smooth wall, there are not...
Abstract In a previous publication in this journal the framework for the development of a model for the road bump problem was laid. The current paper focuses on the aspect of determining the effective distance between two consecutive road bumps developing equations governing the velocity and the wavelength of the motion of the vehicle. The wave equation is re-modelled connecting the isolation factor, linear velocity, wavelength and the frequency of motion of the vehicle over a road bump. A ne...
ABSTRACT A large percentage of Nigerian educational institutions use manual and paper- based system for collecting, processing, and disseminating information. This approach results in inefficient utilization of resources, low productivity and stunted growth of the educational sector. In this study the in-house users- development approach has been used to develop a computer based Educational lnformation Management System (8MS) for a typical University academic department. The existing work Sy...
ABSTRACT Corrugated pipes are pipes with walls of rough surface consisting of dicrete grooves periodicaIly disposed along the flow direction and commonly use in engineering application such as irrigation, delivery devices to main distribution ducts as in transport of Liquid Natural Gas from ships to the mainland distribution network and heat exchanger in heating, ventilation, air-conditioning, etc. The simulation of turbulent, incompressible, isotherminal and single-phase flow is considered f...
ABSTRACT Exergctic analysis of atmospheric distillation plant of Warri Refinery and Petrochemical Company (WRPC) was conducted to evaluate exergy efficiencies and irreversibilities in each unit of the system with aim of identifying potential areas for improvement. The process simulation was carried out using commercial simulator HYSYS® 2003. The results of the simulation compared reasonably well 'with actual plant process parameters with a relative error of 7.22%, Thchighest irreversibility ...
Abstract This paper considers the problem of scheduling in flow-shop by Johnson's Algorithm method, Branch and- Bound Algorithm method and Genetic Algorithm-seethed to find an optimal sequence for n jobs m-machine problem based on minimum elapsed time.ln scheduling the two machine flow shop problem F211 I C, one has to determine a schedule that minimizes the sum of , finishing times of an arbitrary number of jobs that need to be executed on two machines, such that each job must complete proce...
ABSTRACT In this work, modifications have been done on a prototype pneumatic separator to improve its efficiency. The effects of the modifications were studied by carrying out performance test analyses on the two blowers and reciprocating sieve mechanism which make up the critical components of the separating machine. The variations in the feed weights of the sieve were analysed to determine the best and most effective screening process. Also, the best and least tilt angles of the blowers we...
Abstract In order to monitor and control the properties of drilling fluids, measurements are routinely made at the surface. However. these surface measurements may not be representative of down-hole properties where the desired functions of hole cleaning and other related issues are critical to the success of the drilling operations. Consequently, it is important to make necessary adjustments of the fluid properties obtained at ambient conditions to give estimate of properties at high temper...
Abstract- This study utilized fractal disk dimension characterization to investigate the system response of a nonlinear, harmonically driven pendulum of mass, m (or weight. W) and length I over a well-defined parameter plane of excitation amplitude versus damping factor. The system response was simulated at three drive ffequencies (symbol,*) of 1/3, 2/3 and 313. A Runge-Kutta fourth order algorithm, coded in FORTRAN programming language was used to simulate the System response over a 101 by ...
ABSTRACT This study investigated the corrosion resistance of Nickel and Gold plated carbon steels ornamentals in 0.5rno~dd Suphuric acid (&SO4) medium. Nickel plating of carbon steel ' was done in watts solution for 25 minutes with a current density of 3 Aldrn3 at 60°C. The nickel plated carbon steel was later gold plated for 20 minutes with a current density of 0.2 A,ldm3 at 50°C . The plated and unplated carbon steels were exposed to environment for 15 days. The weight loss was taken eve...
Abstract A survey involving the use of questionnaires and personal communication during field trips was carried out in Western Nigeria with the aim of classifying and assessing the efficiency of the existing structures for the storage of crops. Barns; cribs; trenches; platforms; warehouses and silos are among the important. storage structures. The existing structures could be efficient with proper management but a major limitation of most of them is the low unit capacity which is inadequate t...
ABSTRACT Low carbon steel metal is used for the manufacture of nails. Steel wire with
ABSTRACT We have been using polycrystalline thin films of anhydrous cadmium chloride (CdCI2) as an electron beam positive resist for the fabrication of features in SO2- coated silicon wafers The kinetics and mechanism of the electron-beam-induced decomposition of CdCI, which is the resist reaction, have been studied in details this work required that we know the thickness and density of the film. In the ordinary way of things, film thickness and density determination is a routine matter, but ...
ABSTRACT This paper presents the design of a central air-conditioning/ducting system for a case study of a University Senate Chamber in Nigeria. The design aims at maintaining conditions that are conducive to human comfort within the senate chamber of the University (24OC-25.5OC, 50%-55% RH). The design month was March (6) and using the expert assistance found in the carrier system design ducting analysis manual the refrigeration tonnage obtained was 40 and the total air quantity required to ...