ABSTRACT This research work shows us the potential benefits we may obtain from the computerization of the out-patient information system of the Hansa Clinic Enugu. The out-patient department otherwise called OPD is a place where the out-patient that is patients that receive treatment at the clinic without staying overnight, wait for the doctors to attend to them. This manual operation of the outpatient information system is normally stressful. But when it is being computerized it will reduce ...
ABSTRCT The experiment was carried out to analyze comparatively coal and coconut activated carbon. The coal sample used in bituminous and with density of 1300kg 1m3 tile coconut shell was used. The coal and coconut shell was first activated using phosphoric acid. The activated coal and coconut carbons mere then used to bleach palm oil after preliminary treatment of the palm oil. The 10 dine value, saponification value, peroxide value and acid value of the oil bleached with coal activated ...
ABSTRACT The table constructed has a horizontal top with vertical support or legs to raise it from the ground. The aim of the table constructed is for the preservation and storage of useful materials like books, files, computers, result booklets, electronics, office equipments and some vital home equipment etc. However, before the construction of the table, selection of wooden materials were carried out for long and lasting durability of the table. Mahogamy wood was selected for the construc...
INTRODUCTION The most common type of heat exchanger used in industry contains a number of parallel tubes enclosed in a shell and is thus called a shell and tube heat exchanger. These heat exchangers are employed when a process required large quantities of fluid to be heated or cooled. Due to their compact design, these heat exchangers contain a large amount of heat transfer area and also provide a high degree of heat transfer efficiency. Over the years, many different types of shell and ...
ABSTRACT The refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu. The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use of equipment in the pilot plant, so that student would use it in understanding the nature of the flow of fluid through pipe lines, these process was also for the development of the knowledge of every...
ABSTRACT The ill treatment that take place in our motor vehicle Drivers licensing office today, one have to wait endlessly in order to get his driver’s licensing or renew his driver license and so on. This is a problem that is experienced daily, which robs the government a huge sum of money through fraudulent means. Being a system run manually, it is prone to many man-made errors both intentionally and unintentionally, which could be unnecessary delays in attending to customers due to the...
ABSTRACT Voting is a very important process in the Nigerian political system. It is one of the means and most effective method of ensuring a legitimate government through popular participation. To enthrone sound democracy and stability in the political system of the Enugu state a system of rig-free voting has to be put in place. The system would among others discourage double voting, forgery or hoarding of electoral materials massive transfer of ballot papers destruction of ballot boxes, ...
ABSTRACT The magical impact of computer has made enormous contribution to all aspect of the society people can now do things easily unlike in the past. Computers have lesson human activities (effort) in their day to day life, by reducing both human labour and time in solving their problem which are both numerous / unlimited. The introduction of the magical machine has led to the further growth of Agricultural products. The technological know how and scientific research reveals that a lot of w...
INTRODUCTION Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work: digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the transmission may be lacking, for example, in a fan the impeller is mounted directly on the shaft of the electric motor. But in most cases, the transmissi...
ABSTRACT The precise content of this project was to construct a model shell and tube heat exchanger. The material for construction of this project (equipment) and their dimensions are as follows: 1.500mm length of a tube bundle 2.20mm diameter of the tube bundle 3.650mm length of the shell 4.120mm diameter of the shell 5.70mm length of the inlet and outlet 6.20.5mm diameter of the inlet and outlet 7.160mm diameter of the flanges 8.8mm diameter of the holes on the flanges.�...
INTRODUCTION REFRIGERATION Refrigeration is a branch of science that deals with the process of removing heat from a substance or space in order to make it cooler. Refrigerator is defined as a device that is used in cooling the internal temperature below the room temperature (that is between 250C to 300C). Generally, however, for a space or substance to be cooler, it must loss that heat to another. Also, for a space or substance to get hotter, it must absorb heat from another, which must b...
ABSTRACTIn the mechanical engineering department of institute of management and technology there are many machines but it is not all that is functioning well.This may airless as a result of lack of maintenance which is a prove in the breakdown of the air conditioner.The quality and effectiveness of materials were mated very well as referred to machine maintenance.The cost of maintenance was minimized jet reaching a highly victorious rehabilitation.In the course of rehabilitation and repair...
ABSTRACT Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet; precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel. The shelf is made up of 3 partitions. In fabricating the metallic shelf several process where involved. We plundered on the material to be used that can hold...
ABSTRACT Most Stock Marketing Report, production, and manufacturing firms have the basic problem of information flow between the various departments within the organization. This research is intended to highlight the role of a computerized Stock Marketing Report information system in NSEC Compare to the manual system of Stock Marketing Report. To identify the various problems involve in the existing Stock Marketing Report information system of NSEC is the purpose of this research and...
ABSTRACT A Budget being the planning of how to spend revenues and incoming capitals so this makes is necessary to make sure that it is done with extra care. Budgets and the methods of preparing a good one has been a problem to most organization both private and government, the implementation of a faulty budget has brought man companies to a close door point were all operations are stopped. Therefore budget design needs to be accurate and able to give account for every dime spent and on what...