Engineering

Engineering Research Papers/Topics

THE STUDY OF PROPERTIES OF BRIQUETTE PRODUCED FROM GROUNDNUT SHELL COAL BLEND

ABSTRACTBiomass, particularly agricultural residues seem to be one of the most promising energy resources for developing countries (Patomsok, 2008). Rural households and minority of urban dwellers depend solely on fuel woods (charcoal, firewood and sawdust) as their primary sources of energy for the past decades (Onuegbu, 2010). Of all the available energy resources in Nigeria, coal and coal derivatives such as smokeless coal briquettes, bio-coal briquettes, and biomass briquettes have been s...

DESIGN AND CONSTRUCTION OF FOUR-WAY TRAFFIC LIGHT

ABSTRACTThe project “microcontroller based intelligent traffic light system with automatic street light and warning light” was designed to tackle the traffic issues in the country so as to establish automatic traffic control and monitoring system with near perfection. The project intelligent traffic light with automatic street light and warning light is a complex microcontroller based project that was designed to control traffic on a four way road network.The system is embedded with sens...

COMAPARISM OF THE EFFICIENCY OF SAWDUST, COCONUT FIBRE, WOOD CHIPS IN PURIFICATION CRUDE OIL POLLUTED WATER

ABSTRACT A comparative study was conducted among organic waste materials namely coconut fiber, hair, sawdust and woodchips as crude oil absorbents. Twenty grams of each of these materials were wrapped in a pouch and submerged into two set-ups, Set-up A: Pure Crude Oil and Set-up B: Crude Oil with seawater, for an hour. Amount of oil absorbed was gathered and recorded. ANOVA was conducted to verify if the results significantly differed.  The results show that hair had the highest amount of ab...

Technical report on the fabrication of a fan blade

ABSTRACT In recent times, most of the household appliances are using electric power and as such, electricity shortage has become a major problem throughout the world. Ceiling fan is one of such appliances that consume electric power. The best way to minimize the power consumption of the ceiling fan is to reduce the weight of the ceiling fan blade. Thus, this project work entails the design of a new ceiling fan blade in which case the weight and power consumption was compared to the Panasonic ...

ANALYSIS OF BUSH PEAR AND ITS OIL

ABSTRACT The research project studies the analysis of pear and its oil. The mesocarp from edible African pear “DacryodesEdulis” were evaluated for their oil yield. The pulp from this pear were oven dried at 100oC-105oC to a moisture content level of 29%.The mesocarp was subjected to proximate analysis to determine the percentage of the moisture, ash, fat, crude fibre, crude protein and carbohydrate content which resulted to the values of 29%, 2%, 19.6%, 25.5%, 11.9%, and 12% respectively....

DESIGN OF MOLTEN SALT COOLER IN PROCESS PLANT FOR PRODUCTION OF 2-7 X 104 TONNES/YR OF PHTHALIC ANHYDRIDE BY DIRET

ABSTRACTThe general approach to any design of a process plant involve an advanced network of Chemical Engineering processes.  This equipment design project was carried out to design a molten salt cooler (heat exchanger) for production of 2.7 x 104 tonnes/year capacity of phthalic anhydride by direct synthesis of gaseous naphthalene.The information concerning the design of this equipment was gotten from literature review which was then used to obtain the physical properties datas.  The mater...

DESIGN AND CONSTRUCTION OF PUBLIC ADDRESS SYSTEM

INTRODUCTION A public address system is an electronics sound amplification and distribution system with a microphone, amplifier and loud speaker used to allow a person to address a large public. The public address system consists of three main parts namely, the microphone (input transducer), amplifier and the loudspeaker (output transducer). The microphone picks up the sound and convert it to electronic signal in milivolts and this is fed to the amplifier for amplification. In this project, a...

DESIGN AND CONSTRUCTION OF AUTOMATIC EMERGENCY LIGHT

ABSTRACT As the name of the project implies “Automatic Emergency Light” is an electronic system that can provide light during emergency situations i.e when mains (NEPA) supply fails.  This system can provide enough light with full brightness in a given room or office.   The system makes use of white light emitting diodes for the lightings.  It is automatic in operation, in the sense that it can switch itself off when the battery charges full. Automatic Emergency light comprises three s...

DESIGN AND CONSTRUCTION OF 1000VA POWER INVERTER SYSTEM

ABSTRACT As the name of the project implies “Power Inverter”, is an electronics system that converts DC Energy (voltage) to an AC energy.  The major aim of this project is to design and construct a 1000VA Power inverter that is capable of powering loads of equivalent ratings, in the absence of power supply from NEPA or Generator. The system (power inverter) consists of the AC mains sensor section, Relay/change over section, Battery charger section, oscillator section, Driver section, out...

ASSESSMENT OF CARBON MONOXIDE (CO) LEVEL IN ENUGU METROPOLIS MONITORING INDUSTRIAL AND RESIDENTIAL AREA

ABSTRACT Air pollutions pollutant showed that the extent of spreading depends on the motor vehicle traffic population of the area. This pollution strongly generated through combustion of fossil fuels presents difficult environmental challenge to societies as it could degrade the environment and affect human health and quality of life. Vehicular emissions are major contributors to air pollution in urban areas as they contain harmful gases. The levels of carbon monoxide has been investigated in...

EVALUATION OF THE EFFECTS OF FLOODING ON THREE VARIETIES OF RICE (A CASE STUDY OF ABAKALIKI, EBONYI STATE)

ABSTRACT Flooding has been described as one of the most important environmental factors determining the distribution of salt marsh plants. We studied the impact of five water levels on the germination and establishment of the invasive cord-grass spartina deniflora. Plant house experiment was carried out to determine the effects of time and depth of flooding on the survival and growth of rice. Data showed that time and depth of flooding had significant effects on the survival and growth of ric...

EVALUATION OF THE EFFECTS OF ANTHROPOENIC ACTIVITIES AND DOMESTIC WASTE ON SURFACE WATER QUALITY (A CASE STUDY OF EKULU RIVER, ENUGU).

ABSTRACT The microbiological and organic pollutants characteristics of umuosoko stream in ikwuano local government area, Enugu state, Nigeria were carried out. Twenty water samples were collected from four different parts of the river.  The pour plate technique was employed for the isolation of micro-organisms. Colonial morphology, Gram staining and biochemical tests were used for identification and characterization. The statistical analyses used were analysis of variance and standard devia...

MACHINE TOOL CONTROL

INTRODUCTION  The purpose of a control system is to produce a desired output. This output is usually specified by a command input, and is often a function of time. For simple applications in well structured situations, to control, and the controller must have the capability of reacting to disturbance, changes in its environment, and new input commands. The keys element that allows a control system to do this is feedback, which is the process by which a system’s output is used to influence ...

MACHINE COMPONENT DESIGN

DEFINITION OF A KEY  A key is a piece of steel in inserted between the shaft and a hub of the pulley or the gear, mainly to that power. Key are always inserted parallet to the shaft axis. They are need as temporally fastening and are subjected to considerable cursing and shearing stresses.  A key - way in a slut or recess in the shaft and hub of a pulley to accommodate a key.  KEYS A key is a machine member employed at the interface of a pair of mating male and female circular cross-secti...

ENGINEERING DRAWING IN TERMS OF COMMUNICATION

INTRODUCTION Communication means extending information form one person to another in a way in which it can be understood. Information and ideas in technical and scientific fields can very often be more easily communicated through sketching or instrument drawing and blueprint reading. Drawing involves describing the shape and size of an object.  CHAPTER ONE  Preambles Types of Engineering Drawings CHAPTER TWO 2.1STAGES IN THE DEVELOPMENT OF A NEW PRODUCT  2.2THE DRAWING OFFICE  2.3PRINT ...


3256 - 3270 Of 3415 Results