ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method. It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated carbon could be used to trap these impurities, thereby making the product impurity free. The afficac of the absorption using calcium (Cao) �...
ABSTRACT The general approach to any design of a process plant involve an advanced network of chemical engineering process. Absorber is a process plant or equipment that are used in the purification of gas or separation of unwanted gas from the mixture when it comes in contact with the liquid. In this models mass transfer reaction and equilibrium process as they prevail in conventional tray absorbers and in cascade of trickle bed reactors are incorporated. Owring to the mass transfer characte...
ABSTRACT It views of the smoke released when using a firewood for baking cakes, bread, preserve fresh fishes and warming or remove ice form frozen food by some mothers at home, restaurant, fast food shops etc. We discovered the need to design and fabricated kerosene pressurized Oven that will reduce the amount of smoke emitting into the atmosphere and improve the quality of baked food in the society. Kerosine pressurized oven will prevent unnecessary heat from harming the users and lime was...
ABSTRACT The aim of this project is to capture the utilization of pumps for various uses and to maximize the principle of selection of water pumps through the application and pump selection for specific uses our society will transformed wholestically to an industrious nation in the clean water supply for supply for domestic, industrial and down stream sector. Pump parameters and selection are analyzed categorically to enable a good conception in practical. Centrifugal pumps can also be foun...
Note: This work contains only the schematic diagram/design of a biogas plant Biogas typically refers to a mixture of gases produced by the breakdown of organic matter in the absence of oxygen. Biogas can be produced from regionally available raw materials such as recycled waste. It is a renewable energy source and in many cases exerts a very small carbon footprint. Biogas is produced by anaerobic digestion with anaerobic bacteria or fermentation of biodegradable materials such as manure, s...
INTRODUCTION The separation operation of drying converts a solid, semi-solid or liquid feedstock into a solid product by evaporation of the liquid into a vapor phase via application of heat. In the special case of freeze drying, which takes place below the triple point of the liquid being removed, drying occurs by sublimation of the solid phase directly into the vapor phase. This definition thus excludes conversion of a liquid phase into a concentrated liquid phase (evaporation), mechanical d...
ABSTRACT In this research project, the various nail were subjected to six environments so as to check the effect of the environments on corrosion of the nails. Two sets of nails were used; normal nail and concrete nail. Six of each type while the other not coated. The research was carried out in the physical chemical laboratory of the institute of management and technology. The environments used are acidic solution, alkaline solution, salt solution, boiled water, air medium and lubricating...
ABSTRACT This research work was carried out to evaluate the laboratory analysis of pipeline products marketing company (PPMC) depot operations. In the course of the research many scholarly articles on the subject matter were reviewed from which the researcher got lot information concerning the topic at hand. Thus making the research work a reliable source of information as far as facts about petroleum products marketing company (PPMC) is concerned. The Pipeline Inspectorate is charged wit...
ABSTRACT This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot. In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time. The three major products that were considered in this research were premium motor spirit (PMS) automotive gas premium (AGO0 and dual purpose kerosene (DPK). The te...
ABSTRACT This research work was carried out to evaluate the different methods of corrosion prevention, control and monitoring. In the course of the research many scholarly articles on the subject matter were reviewed from which the researcher got lot information concerning the topic at hand. Thus making the research work a reliable source of information as far as facts about corrosion is concerned. To ensure this work satisfies the quality expected of it, an experiment was carried out by ...
ABSTRACT This research project was aimed at optimization of adsorption conditions for removal of methylene blue dye using conventionally activated hamburger seed shell. The activated carbon was first prepared from the hamburger seed shell through carbonization at a temperature of 8000C for 2 hours followed by activation using conc. KOH 9m as activating agent at a temperature if 8500C for 1hour. The prepared activated carbon was then used for the removal of methylene blue from aqueous solu...
ABSTRACT Water is one of the most important substances on earth. All plant and animals must have water to survive. If there is no water there would be no life on earth. Disease causing germs and chemicals find their way into water supplies when this happens, the water becomes polluted. The principal objective of this research work is to asses the impurities found in domestic and industrial wastewater. Other objectives are to asses the presence and absence of organic, inorganic and micro-org...
INTRODUCTION This section briefly describes the main features of pumps and pumping systems. What are pumps and pumping systems? Pumping systems account for nearly 20% of the world’s electrical energy demand and range from 25-50% of the energy usage in certain industrial plant operations (US DOE, 2004). Pumps have two main purposes: 1. Transfer of liquid from one place to another place (e.g. water from an underground aquifer into a water storage tank) 2. Circulate liquid around a system ...
ABSTRACT The technical report presented below is based on the design of mechanism that can be used to open and shut the windows of mechanical engineering workshop from ground level .this mechanism was designed in order to improve safety and convince in their workshop .in the report, the design analysis were made and materials were selected based on operating conditions of each component. The material of the tilt and turn mechanism is cast iron while the material of the lever (handle) is stain...
ABSTRACT This research work was carried out to evaluate the different methods of corrosion prevention, control and monitoring. In the course of the research many scholarly articles on the subject matter were reviewed from which the researcher got lot information concerning the topic at hand. Thus making the research work a reliable source of information as far as facts about corrosion is concerned. To ensure this work satisfies the quality expected of it, an experiment was carried out by th...