ABSTRACT Upstream petroleum industry remains one of the most prolific industries in terms of technology and risk capital transfer. Consequently, governments all over the world try to formulate political as well as economic structures that could favourably attract investments to their petroleum provinces. These structures are spelt out in their petroleum fiscal systems. A good fiscal system tends to find a common ground for both government and the contractor by way of optimizing both efforts ...
ABSTRACT The effect of cooling rate and modification on the microstructure and tensile properties of Al-Si-Mg alloys was carried out. Castings were produced using a stepped pattern that has different section thicknesses. Sand casting technique was used. A thermocouple inserted into the mould cavity recorded the cooling rates for the different sections. The Al5.43%Si3.83%Mg which was melted in the crucible furnace was modified with sodium (Na) and strontium (Sr) in separate cases. T...
ABSTRACT Down-hole temperature and pressure data are important information needed to understand flowing conditions and production optimization. For example, knowing the wellbore temperature profile is useful in predicting the wax formation in the tubing, which is important in flow assurance. While gas production usually causes a temperature decrease due to Joule Thomson effect, water entry results in warming of the wellbore. Warmer water entry is as a result of inflow from a warmer aquifer z...
ABSTRACT The purpose of this study is to develop an innovative technique for optimized gas lift design for marginal fields of the Niger Delta. This study used well data from mature fields located southwest of the Niger Delta to develop optimized gas lift design techniques using the single point continuous gas lift approach. A total of fifty-nine (59) wells from the fields were selected for preliminary screening as potential gas lift candidates. The screening process involved; reviewing w...
Abstract Globally, 30–50% of hydrocarbon volumes in silici-clastic reservoirs are contained within the thin-bedded pay. In the Niger Delta deep water assets, over 30% of in-place volumes are found within the complex turbidites. The presence of multi-pore architecture within such facies makes their description from petrophysics very complex. With the quest for hydrocarbon prospects in frontier deep water settings characterized by such complex rock fabric, detailed reservoir characterization...
ABSTRACT The dynamic simulation is one of the key steps in the validation of the design process of the motor drive systems and it is needed for eliminating inadvertent design mistakes and the resulting error in the prototype construction and testing. A quality mathematical model of induction machine based on the dynamic equations and D-Q transformation technique is presented in rotor reference frame and a computer simulation of a 7.5kW three phase induction motor was carried out based�...
BACKGROUND The numerous limitations of inorganic solar cells has led to keen interest and exploitation of organic solar cells in recent times. They offer several advantages such as lightness, mechanical flexibility, low production cost, ease of processing and have a high potential for large area solar conversion1 . The properties, performance and lifespan of these solar cells depend on the properties of the active layer and interface between the components1 . Thus far research efforts have b...
ABSTRACT In this study, we present a new analytical solution method that accurately corrects the non-isothermal effects from injection and fall-off tests. The derivative of these solutions is applied to develop the Tiab's Direct Synthesis (TDS) technique. New equations have been developed to determine the different reservoir parameters from pressure injection/fall-off test data. The flow regimes that can occur during an injection test or fall-off test are obtained by separating the different...
ABSTRACT Drilling fluids play sophisticated roles in the drilling process which include, keeping formation fluids at bay, stabilizing the wellbore without damaging the formation, lubricating the bit and drill-string and clearing cuttings from the bit face. Weighting agents are compounds that are dissolved or suspended in drilling fluid to increase its density. The effect of density also contributes to the stability of the borehole by increasing the pressure exerted by the wellbore fluid onto...
ABSTRACT Reservoir characterization has long been identified as the ultimate process employed in detailed description of a reservoir in order to properly book the reserve and also to optimally place the wells and drain the reservoir. This report details the workflow of reservoir „X‟ study, right from 3D seismic interpretation to delivery of a 3D static model of the reservoir by fully integrating all the available data in the field: 3D seismic data, well logs, deviation data, core data, c...
ABSTRACT In the design of flood control structures, there is need for rainfall intensity estimation for design discharge computation. To make the rainfall intensity values easily available in south-east and south-south Nigeria, this research developed rainfall models. Dimensional and Regression analyses were used to produce models of rainfall intensities. The dimensional models are dimensionally balanced as opposed to the other models which are based on Talbot, Benard and Quotient ...
ABSTRACT The design of natural flow and artificial lift tubing strings for the whole life of a water drive reservoir was carried out using data based on synthetic reservoir performance based on a material balance. The effects of reservoir properties on the life of the well was also investigated. Constraints such as maximum production, maximum drawdown, limitations on surface facilities capacities, as well as available gas lift was imposed. The production conditions for natural flow, continuo...
ABSTRACT Simplified predictive numerical models have been developed for diffusion rate of crude oil spilled into Niger Delta soils. The proposed model equations were developed using Fourier transformation, and Green’s function. The induction principles as well as the indicial matrix method of dimensional analysis were adopted in determining the functional parameters that could possibly influence their diffusion rates. These mathematical models correctly predict one – dimensional ...
ABSTRACT A data-driven approach to solving the problem of excess water production was the focus of this study. In this research, several reservoir models were simulated for 26 years, and data obtained after simulation was used to develop two artificial neural network models to predict the water cut for various producers. The first 22 years of data obtained from simulation was used to train the first neural network model, and the model was then used to forecast the water cut for the last four...
ABSTRACT New Biodegradable drilling fluids were developed using Brachystegia eurycoma (achi), Detarium microcarpum (ofo) and Pleurotus (osu). The drilling properties such as yield point, apparent viscosity, low shear rate yield point and fluid loss were determined.The field polymer muds that are currently in use namely; PAC-R and PAC-L were formulated and used as control samples to the new proposed product. Herschel –Buckley model was used to obtain the yield stress. Cutting transport rat...